top of page

Videojet 9550
applicators and accessories

Applicators and accessories for Videojet 9550

Especially in terms of throughput and print speed of up to 500 mm/sec in the label printing and dispensing area, you can hardly get past the Videojet 9550. However, the applicators available on the market are often not sufficient to use the Videojet VJ9550 in all applications in the 4" (100 mm) print area.

For this reason we have developed various applicator models to expand the range of applications of the VJ9550. All applicators are available in LH and RH variants. In addition to the required hardware, each applicator kit also includes the applicator board (I/O module) specially developed by us for the VJ9550.

If your application cannot be covered by our available kits, please contact us! We will find the right solution.



The SSA applicator is available in different stroke lengths from 80 - 200 mm. The linear stroke enables labeling with a performance of up to 120 labels/min. (depending on label length and stroke length). The module can optionally be equipped with multi-chamber vacuum plates in order to apply different label sizes with one vacuum plate. Different product heights can be processed with the optionally available distance sensor.

Videojet application

Videojet Application - VJ9550-SSA

Perfect in the run!

Features and scope of delivery

As an option to the extended dispensing tongue, the angle of which can be ideally adjusted to the film run of the packaging machine, a mobile floor assembly module is also available, which allows the unit to be moved transversely to the film run direction for material changes or for placing the labels. Quick-release fasteners at the necessary positions and measuring scales make it easier to switch to different labeling positions. The register roll, which also has a measuring tape, is used for the exact positioning of the labels on the dispensing tongue and can be adjusted in a matter of seconds.

Videojet integrations
VFFS kit

The image on the left shows the VJ9550 incl. VFFS-KIt and floor mounting module - fully equipped for installation in a vertical tubular bagging system.

Fast and accurate around the corner

This corner applicator was developed to apply a label to the corner of cardboard boxes so that the shipping case label can be read from both sides.  

Since the module was developed in close cooperation with Videojet, both components are precisely matched to each other. This means that the corner wrap label can be completely applied within 2 seconds. Labeling can be either front/top or top/back. Both the RH and the LH variants are available from stock. The device is designed for a label size of 100 x 300 mm.

Videojet applications

Videojet Integrations - VJ9550-FCW-RCW

Logistics Labelling
Corner labelling

Corner labelling

in front

Corner labelling



Detached from the carrier material - with vacuum belt


Labelling detached from the carrier material

Labeling with vacuum tape

Labelling without liner

Labeling with vacuum tape

Features and Options

The VCB enables the labels to be applied separately from the carrier material in order to compensate for either uneven product surfaces or different transport speeds of the product. Even if the product stops during the labeling process and is transported on again, the label application works perfectly, since the peeling speed of the label determines the initial contact between the label and the product.

The module is equipped with a stepper motor, a label stop sensor on the dispensing edge, a sponge rubber roller or brush to reroll or brush the label after it has actually been applied, and its own microprocessor control to be able to process different recipes and formats on the system without changeover times.  

The vacuum tape is available in different lengths (depending on the maximum label length).

Installation position:

horizontal Vertical

The ultra-fast linear applicator SSA VJ9550


Linear applicator
Linear applicator


80 mm stroke and format vacuum plate


200 mm stroke and mold vacuum plate


300 mm stroke and format vacuum plate


400 mm stroke and format vacuum plate


500 mm stroke and format vacuum plate

Videojet applicator integration


600 mm stroke and format vacuum plate

equipment options

Ultrasonic sensor for product scanning, barcode scanner for label presence control,

Blow-on module (air box)

installation position

horizontal Vertical

bottom of page